Inscrivez-vous pour débloquer vos prix B2B exclusifs et commencez vos achats. Inscrivez-vous maintenant!
Impulse switch with integrated relay function, 1 NO contact 10A
En stock: Non
Stock fournisseur: Non
Quantité minimale de commande: 1
Prix (hors TVA):
37,74 €
EAN: 4010312107911
MPN: 61100001
Colis: 1
Délai de livraison estimé à notre entrepôt (environ):
2-4 weeks
Technical Information
| État de l’article | Nouveau |
| Nom du fabricant | Impulse switch with integrated relay function, 1 NO contact 10A |
| Marque | ELTAKO |
| Catégories |
Relays
|
| Pays d’origine | CN |
| Code du système harmonisé | 8536 5080 00 |
| Méthode de montage | Montage encastré (plâtre) |
| Fonction | Electronique avec retard de déclenchement |
| Profondeur d'encastrement | 58 mm |
| Largeur en nombre d'espacements modulaires | 1 |
| Tension de contrôle 1 | 8-230 V |
| Tension de commande 2 | 10-230 V |
| Type de tension de commande 1 | AC |
| Type de tension de commande 2 | DC |
| Tension de contrôle de la fréquence 1 | 50 Hz |
| Tension de commande de fréquence 2 | 50 Hz |
| Adapté au fonctionnement manuel | No |
| Type de tension d'alimentation | AC/DC |
| Tension d'alimentation | 230 V |
| Charge max. lampe à incandescence | 2000 W |
| Charge max. lampe fluorescente | 1000 VA |
| Charge max. lampe fluorescente (circuit Duo) | 1000 VA |
| Charge maximale lampe fluorescente (parallèle compensée) | 500 VA |
| Courant nominal de commutation | 10 A |
| Nombre de contacts comme contact normalement fermé | 0 |
| Nombre de contacts comme contact normalement ouvert | 1 |
| Nombre de contacts comme contact inverseur | 0 |
Détails d’emballage
| Niveau d’emballage 1 | 4010312107911, 4010312107911 |
| Niveau d’emballage 2 | 4010312107911 |
| Niveau d’emballage 3 | 4010312107911 |
Téléchargements
Description
1 NO contact not potential free 10A/250V AC. 230V LED lamps up to 600W, incandescent lamp load up to 2000W. Off delay impulse switch with switch-off early warning and pushbutton permanent light switchable. Standby loss 0.7 watt only. For installation. 45mm long, 45mm wide, 18mm deep. Zero passage switching to protect contacts and lamps. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Control voltage 230V. In addition electrically isolated universal control voltage from 8 to 230V UC. Supply voltage and switching voltage 230V. Very low switching noise. Variable time range up to 120 minutes in the function ESV. At the control input pushbuttons with a glow lamp current up to 50mA can be connected. In case of a power failure the system is disconnected in a preset sequence. If the timing period is set to minimum in the function ESV, the release delay is switched off. The standard impulse switch function ES is then set. The function ER is selectable. If the function ER is selected a glow lamp current is not permitted. Only the control input A1-A2 should be used. When set to the function ER this device is suitable to feed back the switching voltage signal of a dimmer switch. If switch-off early warning function is switched on, the light starts flickering approx. 30 seconds before time-out. This is repeated three times at decreasing time intervals. If the permanent light function is switched on, the function can be activated by pressing the pushbutton for longer than 1 second. This function switches off automatically after 2 hours or by pressing the pushbutton for longer than 2 seconds. If both switch-off early warning function and permanent light by pushbutton are set, the switch-off early warning function is activated before switching off the permanent light.