WAGO Lighting accessories
Install teams use WAGO on lamp-side work when they need fast, repeatable terminations that pass pull tests, hold IP after maintenance, and keep SELV/mains separation obvious inside small spaces. The assortment below maps the pieces you actually stock for downlights, lines, pendants, bulkheads, and service swaps.
wago lighting accessories selection and field roles
The wago lighting accessories portfolio sits between gear tray and trim: in-canopy wiring blocks with probe points, strain-relief clamps that move load off terminals, grommets sized to jacket Ø, and sealing sets that protect IP in bathrooms and exterior soffits. Crews build a matrix by fixture family—conductor window, strip length, gland thread, and seal type—so night changes don’t alter photometry or ingress.
wago mounting kits room bundles and retrofit details
Room packs under wago mounting kits combine the exact box/plate, compression glands (M16/M20) with stated clamp ranges, strain-relief hardware, and label windows. Spacer rings (2–10 mm) correct proud plaster; repair collars clean up oversize cutouts; divider plates maintain SELV spacing when control and mains share a canopy. Stocking by ceiling type (mineral grid, plasterboard, metal) keeps torque and strip rules consistent from bay to bay.
wago lighting connectors quick coupling and loop-through practice
For fast finishing above ceilings, wago lighting connectors cover 2–5-pole lever and push-in sets with keyed housings, clear insertion windows, and isolate-for-test positions. IP20 pairs handle dry voids; sealed plugs with matching thread sets protect damp heads. Loop-through blocks carry feed/return plus 1–10 V or DALI lines; polarity embossing and color cues prevent crossed dimming cores under low light.
wago lamp holders temperature classes and cap formats
Where fixtures retain replaceable sources, wago lamp holders address the hot end: ceramic bodies for 200–250 °C zones, high-temp polymers where tc is lower. Coverage includes E27/E14, GU10/GU5.3, G9, G13/G5, GX53, and R7s with anti-rotation tabs and earth lugs placed for short pigtails. Pre-terminated tails (0.5…1.0 mm²; strip 8–10 mm) help pass pull tests on lifts.
wago lighting components through-wiring blocks and strain relief
Above canopies and inside gear trays, wago lighting components provide L/N/PE bays separated from control cores, bridge links for rows, and cord grips that anchor jacket—not conductors. Test points stay visible after fit-off, and ferrule-friendly cages make maintenance predictable.
wago installation accessories sealing, adapters, and SELV barriers
Bathrooms and housekeeping areas rely on wago installation accessories: IP44 gasket rings, sleeves for clean cable pass-through, and color-coded barriers to keep SELV/mains segregation obvious. Adapter plates rescue legacy cutouts without shifting bezel lines; matching screw packs keep torque in spec for the host material.
wago spare parts for lighting drivers, optics, and seals
Service stock tagged as wago spare parts for lighting includes driver trays (CC/CV) with stated tc, emergency modules, opal/prismatic diffusers, reflector/lens kits, and replacement gaskets. Packaging carries strip/torque notes and thread sizes so a night swap restores IP and beam shape rather than changing it.
Other lighting accessories
| zumtobel lighting accessories |
| trilux lighting accessories |
| tridonic lighting accessories |
| thorgeon lighting accessories |
| sylvania lighting accessories |
Technical specifications and standards that matter
Supply interfaces 230 V AC for mains, SELV 12/24 V for controls; dimming lines 1–10 V or DALI kept distinct. Connector windows commonly 0.2…4 mm² (lever) or 0.5…2.5 mm² (compact); strip 8–11 mm as marked on parts. Ingress to IEC 60529 (IP20 ceilings; IP44/65 with listed kits). Glow-wire ratings 650–850 °C per component family. Where applicable: inline connectors to IEC/EN 60998; rail terminals to IEC/EN 60947-7-1/-7-2. Apply 360° braid clamps near drives to control common-mode noise.
Applications and compatibility
• Offices/hospitality: quick plugs in modular ceilings, gasketed sets in wet points, low-ripple drivers for camera-heavy areas.
• Education/healthcare: LSZH plastics where routes demand it, tamper-resistant trims, clear label windows for audits.
• Logistics/plant: sealed plugs, anti-vibration clips on high bays, ceramic caps around hot canopies.
All parts align with common device grids (Ø68 mm, 60 mm screw line, 71 mm pitch) so trim and IP survive maintenance.
Integration with other brand products
Accessories interface cleanly with typical downlights, panels, bulkheads, and pendant canopies; thread sets match standard box glands; label formats mirror panel legends so circuit IDs remain readable after refit.
Selection criteria for B2B buyers
- Fix environment first: IP/IK and cleaning regime → choose seals, materials, and gland thread.
- Define electricals: conductor size/class, strip length, torque window; set dimming cores and loop-through need.
- Lock geometry: ceiling type, adapter/spacer requirements, barrier use for SELV.
- Publish test practice: pull tests, insulation, polarity, loop/Zs at the plate with probe access noted.
- Tie spares to fixture EANs so drivers, optics, and seals land as a matched set.
Advantages of working with Bankoflamps
Get individual B2B pricing with custom offers and a dedicated account manager. Quotes arrive fast—around an hour—and orders place quickly by EAN/MPN. You have real-time stock visibility across EU warehouses, downloadable price lists that stay current, and clear lead-time and order-status tracking. Purchase history and analytics are available in the portal. Trusted clients can use post-payment terms up to 30 days. We manage consolidated shipments to reduce delivery costs, keep pricing stable with validity dates, and serve clients in France, the Baltics, Germany, Spain, Italy, Belgium, and the Netherlands.