THORGEON Built-in mounting lamps
thorgeon built in mounting lamps optical and mechanical profile
Lumen packages span 900–5 000 lm at 2700/3000/3500/4000 K, CRI 80 by default with CRI 90 for front-of-house. Efficacy typically 110–145 lm/W with PF ≥ 0.95, THD < 10 %, surge 2–4 kV. Thermal design targets L80 50–70k h when Tc is respected and 7.5–10 mm breathing is kept above the gear tray. Frames use reinforced PC/steel with closed-cell EPDM or silicone gaskets; trims keep one collar depth so drill jigs repeat room-to-room. For EMC, shields land 360° at the entry plate and SELV/mains lanes are separated with divider strips. Section kits, trims, and optics are shared with thorgeon integrated mounting lamps to simplify spare holding.
thorgeon recessed luminaires distributions and spacing
Opal, micro-prism UGR < 19, and corridor lenses cover open offices, task zones, and long runs. At 2.7–3.0 m, plan by centre-beam candela and “beam-edge” spacing to hold 0.6–0.7 uniformity on aisles. Emergency variants publish 120–500 lm maintained output with self-test indicators. Where ceilings repeat, keep one lumen bin per height so thorgeon built in mounting lamps deliver identical lux without re-aiming.
thorgeon flush mount lights installation details
Shallow bodies avoid duct clashes and keep sprinkler throw clear. Captive screws, keyhole slots, retained gaskets, and through-wiring (3×1.5/2.5 mm²) reduce ladder time. Terminals accept 0.5…2.5 mm² Cu, strip 8–10 mm; torque 0.5–0.8 Nm. IP20 in clean interiors, IP54/IP65 where humidity or dust is present; IK08–IK10 hardware for public areas. Maintenance teams tag trays by optic and CCT so swaps in thorgeon recessed luminaires don’t alter spacing tables.
thorgeon built in led fixtures drivers and control
DALI-2 and 0–10 V dim to 5–10 % with linear or log curves; selected sizes support quiet trailing-edge for retrofit boards. Flicker metrics satisfy common office guidance (PstLM/SVM) on approved controls. Corridor function pairs presence and daylight hold; maintained emergency kits (LiFePO₄) offer 1 h/3 h autonomy with 12–24 h recharge. When scenes must clone across floors, estates lock control type, minimum level, and CCT—those choices also govern glare planning for thorgeon flush mount lights.
thorgeon ceiling recessed lighting applications and retrofits
Apartments and hotels run warm CCT with opal trims; offices use micro-prism optics to balance UGR and verticals; logistics corridors need corridor beams at higher mounting. Legacy cut-outs are preserved with spacer rings and adapter plates; “enclosed-rated” SKUs protect sealed cups. For phased refresh, document Tc at 60 min, gland size, and ferrule windows once, then repeat the same pack on every floor—this keeps thorgeon built in led fixtures predictable during churn. In galleries, combine CRI 90 with tight 24° optics to lift accents, while thorgeon embedded led luminaires in opal finish maintain background levels.
thorgeon integrated mounting lamps accessories and sealing
Entries remain metric M16/M20/M25; matched ferrules maintain IP after servicing. Drain/breather plugs manage pressure cycles in humid corridors; stainless A2/A4 hardware suits ammonia or coastal air. Spacer rings correct uneven plaster and keep bezel planes flush. Publish strip windows, torque, and pull-out in the drawing set so acceptance is quick; this is the same documentation approach used for thorgeon ceiling recessed lighting in mixed-use estates.
thorgeon embedded led luminaires selection criteria for B2B buyers
- Fix target illuminance and mounting height, then choose optic (opal, micro-prism, corridor) and lumen class.
- Lock CCT/CRI by palette—CRI 90 for retail/reception, CRI 80 for general zones.
- Choose control topology (phase-cut, 0–10 V, DALI-2) and publish minimum level/curve.
- Confirm IP/IK by zone; verify Tc at pilot room; record gasket compression and bracket offsets.
- Capture ferrule size, gland thread, strip window, torque, and emergency autonomy in the worksheet.
Procurement keeps one code per zone so thorgeon embedded led luminaires look identical after churn and spares stay lean.
Advantages of working with Bankoflamps
We ship in the sequence crews install. You get project-specific pricing, live EU stock before teams are booked, and quotes with EAN/MPN in roughly one hour. The portal shows lead times, shipment progress, and downloadable price files with validity windows you can plan around. Trusted accounts use post-payment up to 30 days. We consolidate by room bundle so luminaires, glands, collars, sensors, and emergency packs arrive together, and a dedicated manager checks lumen bins, optics, control method, autonomy class, gland threads, ferrule sizes, and torque notes against your drawings—keeping kits site-ready across France, the Baltics, Germany, Spain, Italy, Belgium, and the Netherlands.