Shada High bay

shada highbay lights for modern plants and logistics

Shada targets the heavy lifters of interior lighting: tall bays, wide aisles, and production floors that run hot and dusty. Housings come in round die-cast “UFO” forms and slim linear bodies for racking. Typical light packages span 10–40 klm with neutral or cool white options that keep color rendering stable across shifts. Installers get roomy gear compartments, sealed glands, and brackets that don’t flex under load, so units hang true even on long drops.

shada industrial highbays range and mounting options

Expect two core styles. Round units cover open areas and crane bays; linear bodies line up with aisles and conveyors. Hook, ring, and yoke mounts are standard, with safety-wire points sized for 2–3 mm cables. For heights of 6–12 m, mid-power packages with wide beams work well; 12–18 m often pairs high-intensity engines with 60° or aisle optics. Emergency variants accept remote packs, and control-ready versions ship with knockouts for DALI-2 or 1–10 V nodes.

shada led highbay luminaires optical and electrical design

Optics include deep reflectors, prismatic diffusers for glare control, and aisle distributions around 30×90° to push light down racking. Efficacy typically lands in the 150–190 lm/W band depending on CCT and driver choice. Expect CRI 80 as the baseline with CRI 90 options for QA and color work; common CCTs are 4000 K and 5000 K. Drivers run at PF ≥0.95 with THD ≤10–15 % in nominal load, surge protection in the 4–6 kV L-N and 6–10 kV L/N-PE range, and inrush-tamed inputs for dense circuits. Thermal paths are generous: finned sinks, large interface pads, and driver bays separated from LED boards. Lifetime data is typically stated as L80 or L90 at 50–100k h with TM-21 projections from LM-80 LED data. Ambient ratings sit around −30…+45 °C; choose high-temp skus when roof decks run hot. Ingress protection is generally IP65–IP66 with IK08–IK10 impact classes for ball guards and loading zones.

Technical specifications and standards

Lumen maintenance and safety follow familiar references such as IEC 60598 for luminaires, EN 62471 for photobiological safety, and EMC to EN 61000 series. Control interfaces include DALI-2, 1–10 V, and volt-free input for step dim. Many units support sensor sockets for presence/daylight harvesting. UGR management matters in low-gloss floors—use diffused lenses or lower luminance engines to stay within project targets. For power distribution, design feeders around steady-state draw plus inrush profiles; group switching with contactors rated for LED drivers.

Applications and compatibility across facilities

Aisle lighting benefits from narrow beams that keep lux on the pick face while limiting spill. Open assembly floors use 90–120° optics for uniformity with fewer poles. Wet or dusty zones need gasketed housings and stainless fixings; cold storage prefers drivers validated for low-temperature start. Integrators rolling out shada warehouse lighting frequently pair linear highbays with daylight sensors on perimeter aisles to cut afternoon load. In machine shops, glare shields and side louvers help operators read instruments without washout. For bench areas, task layers complement the grid rather than chasing ever-higher bay levels. Where benches and lifts move often, note provisions for quick-release links on drops—fast to re-hang, less time at height.

shada highbay accessories for installation and service

Accessory sets cover wire-rope kits with turnbuckles, rigid drop rods, ball guards, polycarbonate lenses, glare caps, plug-in sensor heads, and emergency pods rated 1–3 h. Pre-terminated leads reduce time on scissor lifts. For dusty plants, add breather vents to minimize fogging; in corrosive corners, specify stainless clips and coated fasteners. Maintenance teams keep spare lenses, gaskets, and driver trays to swap assemblies without taking the whole luminaire down.

Integration with other Shada products

Routing and terminations align with Shada installation hardware. Use IP-rated junction boxes with compression glands, divider strips when mains and control share trunking, and swivel brackets from the mounting range for tilt aiming over racking. For fast rollouts, prebuild strings on the floor with Shada lighting connectors and lift as units. If you need local isolation, fit compact switch pods from the accessories line on the yoke for safe service at height. For small adds, portable towers from the brand’s work-light lineup can bridge gaps until the next shutdown.

Selection criteria for B2B clients

Start with task planes and mounting height. Map target lux, then select beam: 60° for high shelves and long throws, 90° for mixed spaces, 120° for open floors. Lock CCT by area—4000 K for accurate color work, 5000 K for visual punch. Confirm driver interface to match the site’s control backbone and reserve 20–30 % headroom in PSU wattage for thermal derating. Where forklifts operate, plan IK and cage requirements. For production lines, stroboscopic visibility matters—favor drivers with high-frequency modulation or documented percent flicker to avoid machine-vision artifacts. When capex must show quick returns, specify shada energy efficient highbays with sensor-ready gear and daylight dimming baked into the submittal. In tool zones and vocational classrooms, reference shada workshop highbay fixtures so glare and mounting geometry reflect bench work rather than racking.

Advantages of working with Bankoflamps

We align pricing to your bay counts and mounting heights, then show live EU stock before lifts are booked. Quotations land in about an hour with EAN/MPN so optics, CCT, and control gear don’t drift between phases. Your portal exposes lead times, shipment status, and downloadable price files; price-validity windows stay stable across rollouts. Approved clients can use post-payment up to 30 days. We consolidate partials to cut freight, and your account manager cross-checks optics, driver interface, PSU margin, surge rating, IP/IK class, hang hardware, and connector types against your drawings—so pallets arrive site-ready and crews spend their time at height installing, not reworking.