Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
Room Controller Touch, signal white, gloss, with Legacy firmware for SHC and CSAU
Laos: Ei
Hankija laovaru: Ei
Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
130,12 €
EAN: 9010653030300
MPN: EP-500836
Pakend: 1
Karp: 60
Hinnanguline tarneaeg meie laos (umbes):
4-6 weeks
Technical Information
| Toote seisukord | Uus |
| Tootja nimi | Room Controller Touch, signal white, gloss, with Legacy firmware for SHC and CSAU |
| Bränd | EATON |
| Kategooriad |
Bus System Devices (KNX/Modbus)
|
| Päritoluriik | CZ |
| Harmoneeritud süsteemi kood | 8536 5011 00 |
| Kooste ehitus | Põhielement täiskorpusega |
| Siinisüsteem KNX | No |
| Raadiosageduslik siinisüsteem | Yes |
| Siinisüsteem Powernet | No |
| Siiniühendusega | Yes |
| Muud siinisüsteemid | xComfort |
| Siinisüsteem LON | No |
| Siinisüsteem KNX radio | No |
| Raadiosageduslik, kahesuunaline | Yes |
Pakendamise üksikasjad
| Pakkimistase 1 | 9010653030300 |
| Pakkimistase 2 | 9010238226333 |
Muud tehnilised andmed
| Paigaldusviis | Pinnapealne |
| Värvus | Valge |
| Pinnatöötlus | Töötlemata |
| Kuvariga | Yes |
| Materjal | Termoplastist |
| Digitaalsisendite arv | 0 |
| Materjal | Plast |
| Vargusevastane/lahtimonteerimiskaitse | No |
| Käsisäte | Yes |
| Võimalik on paralleelne hooldus | Yes |
| Kohalolunupp | No |
| RAL-number (akin) | 9003 |
| Kaitseaste (IP) | IP20 |
| LED näidikuga | No |
| Läbipaistev | No |
| Pinna liik | Läikiv |
| Lokaaljuhtimisega | Yes |
| Temperatuurijuhtimise klass | IV |
| Ooteoleku võimsustarve (solstandby) | 0.05 W |
| Sisseehitatud paigalduskarbi vähim sügavus | 0 mm |
| Välisandur | Yes |
Kirjeldus
Room Controller Touch, signal white gloss, with temperature and humidity sensor is suitable to monitor and control the climate in a room either stand-a-lone or together with an intelligent device. The operation is done through the Touch display with backlight. The user programmable Week Program Timer and 4 Operation modes offer maximum flexibility to meet the specific needs. It supports floor temperature control via an optional external wired floor temperature sensor (PT1000). Two optional touch-buttons on the display are available to control other xComfort functions/actuators . The Room Controller Touch is compatible with many 55 mm frames from the switch industry (observe the compatibility list). The device is battery powered and NO switch, branch or installation box is required, therefore it can be easily mounted anywhere (screwed and glued). Battery included as standard, but it can also be powered with an optional mains power adapter.This Room Controller Touch is pre-programmed with the Legacy software that works with the xComfort SHC, Switching actuator and Heating actuator.