Registreeru, et avada oma eksklusiivsed B2B hinnad ja alustada ostlemist. Registreeru kohe!
Powerline actuator 1 channel with sensor input 230V
Laos: Ei
Hankija laovaru: Ei
Minimaalne tellimuse kogus: 1
Hind (ilma KM-ta):
93,95 €
EAN: 4010312316665
MPN: 31100001
Pakend: 1
Hinnanguline tarneaeg meie laos (umbes):
2-4 weeks
Technical Information
| Toote seisukord | Uus |
| Tootja nimi | Powerline actuator 1 channel with sensor input 230V |
| Bränd | ELTAKO |
| Kategooriad |
Bus System Devices (KNX/Modbus)
|
| Päritoluriik | CN |
| Harmoneeritud süsteemi kood | 8526 9200 00 |
| Siinisüsteem KNX | No |
| Siiniühendusega | Yes |
| Siinisüsteem LON | No |
| Siinisüsteem KNX radio | No |
| Raadiosageduslik, kahesuunaline | No |
Pakendamise üksikasjad
| Pakkimistase 1 | 4010312316665, 4010312316665 |
| Pakkimistase 2 | 4010312316665 |
| Pakkimistase 3 | 4010312316665 |
Muud tehnilised andmed
| Paigaldusviis | Süvistatud paigaldus (krohvi) |
| Tunnusvool | 10 A |
| Väljundvõimsus | 2000 W |
| Tunnus-talitluspinge | 230 V |
| Raadiosageduslik siinisüsteem | No |
| Siinisüsteem Powernet | Yes |
| Suurim lülitusvõimsus | 2000 W |
| Suurim lülituskontaktide arv | 1 |
| Suurim lülitusvool | 10 A |
| Muud siinisüsteemid | Puudub |
| C-koormus | Yes |
| Eri faaside ühendamine | No |
| Lokaaljuhtimine/käsijuhtimine | Yes |
| LED näidikuga | Yes |
| Laiendusmoodulitega | No |
| Eemaldatav siini moodul | No |
| Sisseehitatud paigalduskarbi vähim sügavus | 25 mm |
| Max. switching power LED | 400 W |
Allalaadimised
Kirjeldus
Powerline actuator with 1 channel with sensor input. 53x43mm, 25mm deep, for mounting in 58mm switch boxes. Used as impulse switch or relay. 1 NO contact not potential free 10A/250V AC, incandescent lamps 2000 watts. Sensor input 230V. Standby loss only 0,5 watt. To control and switch at the same place. Two rotary switches are located on the front for address assignment: The left rotary switch defines the group address g with 16 alphabetical values from A to P. The right rotary switch defines the element address e with 16 numerical values from 0 to 15. Above it is a slide switch which acts as a configuration switch with positions 0, 1 and 2. Position 0: Sensor input functions as pushbutton (impulse switch). Position 1: Sensor input functions as NO contact (relay). Position 2: A change-over switch is evaluated as a pushbutton. All entries and configurations can also be accessed via the mains using the PC software SIENNA Professional. This means that another configuration can also be set that is not available via the rotary switches: Position 3: Sensor input acts as NO contact (relay inverse). To the left of the rotary switches is a red LED which indicates all activities. Next to it is a reset pushbutton and to the right of that is a service pin. For functions, please refer to the operating instructions. The terminals located above are plug-in terminals for conductor cross-sections of 0.2mm² to 1.5mm².