Regístrese para desbloquear sus precios B2B exclusivos y empezar a comprar. ¡Regístrese ahora!
Staircase time switch, 1 NO contact 10A image 1

Staircase time switch, 1 NO contact 10A

Solo bajo pedido
EAN: 4010312400791
MPN: 61100102
Embalaje: 1
Precio (sin IVA)
38,20 €
por unidad
Cantidad mínima de pedido: 1
Tiempo de entrega a nuestro almacén: 4-6 weeks
Este precio es válido hasta la siguiente lista de precios o hasta agotar existencias

Información técnica

Estado del artículo Nuevo
Nombre del fabricante Staircase time switch, 1 NO contact 10A
Marca ELTAKO
Categorías Placas de identificación y cajas
País de origen* CN
* El país de origen real puede variar según el lote de suministro. Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
Código del Sistema Armonizado 8536 5080 00
ETIM EC000297
Tipo de fijación Montaje empotrado (yeso)
Función Electrónico con preaviso de desconexión
Retardo de disparo 1-12 min
Tensión de control 1 230 V
Tipo de tensión de control 1 AC
Frecuencia de la tensión de control 1 50 Hz
Sistema de cableado Configuración de 3 y 4 conductores
Aviso de desconexión Intermitencia
Repetitivo Repetitivo + luz continua + prolongación de tiempo
Tipo de tensión de alimentación AC
Tensión de alimentación 250 V
Carga máx. de lámparas incandescentes 2000 W
Carga máx. de lámparas fluorescentes 1000 VA
Corriente nominal de conmutación 10 A
Función seleccionable de desconexión de corriente No
Indicador de potencia LED máx. 200 W

Detalles del embalaje

Nivel de embalaje 1 4010312400791, 4010312400791
Nivel de embalaje 2 4010312400791
Nivel de embalaje 3 4010312400791

Otros datos técnicos

Profundidad de montaje 18 mm
Ancho en módulos 0
Carga máx. de lámparas fluorescentes (circuito doble) 1000 VA
Carga máx. de lámparas fluorescentes (compensación en paralelo) 500 VA
Corriente de lámpara incandescente del pulsador 50 mA
Número de contactos normalmente cerrados 0
Número de contactos normalmente abiertos 1
Número de contactos conmutados 0

Descargas

Descripción

1 NO contact not potential free 10A/250V AC. 230V LED lamps up to 600W, energy saving lamps ESL up to 200W, incandescent lamps up to 2000W. Switch-off early warning and permanent light by pushbutton switchable. Standby loss 0.7 watt only. With ESL optimisation. Built-in device for installation. 45mm long, 45mm wide, 18mm deep. Zero passage switching to protect contacts and lamps. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Control voltage, supply voltage and switching voltage 230V. With infinitely variable time range from 1 to 12 minutes. 50mA glow lamp current, dependent on the ignition voltage of the glow lamps. 3-wire and 4-wire circuits, resettable, with attic lighting if 4-wire circuit. Automatic detection of the method of connection. After a power failure the lighting is switched on again in case the set time has not elapsed yet. If switch-off early warning function is switched on, the light starts flickering approx. 30 seconds before time-out and is repeated three times at decreasing time intervals. If permanent light by pushbutton is switched on, permanent light can be switched on by pressing the pushbutton longer than 1 second. This is switched off automatically after 60 minutes or by pressing the pushbutton longer than 2 seconds. If both switch-off early warning function and permanent light by pushbutton   are switched on, the switch-off early warning function is activated before the permanent light switches off. When energy saving lamps ESL are completely or partially switched, then set the switch-off early warning with the pushbutton permanent light ESL on the lower rotary switch. If the function TLZ is selected the time can be extended within the first second after switching on or resetting by pressing the pushbutton repeatedly up to three times (incrementing). Each momentary-contact control increments the set time once. The function ESV, impulse switch with release delay up to 120 minutes, can be selected optionally. If this function is set it is automatically disconnected after the set delay is timed out if a manual OFF command has not been given. If the timing period is set to minimum in the function ESV, the release delay is switched off. The standard impulse switch function ES is then set.