Regístrese para desbloquear sus precios B2B exclusivos y empezar a comprar. ¡Regístrese ahora!
Wireless actuator constant current LED dimmer switch image 1

Wireless actuator constant current LED dimmer switch

Solo bajo pedido
EAN: 4010312314357
MPN: 30100836
Embalaje: 1
Precio (sin IVA)
71,82 €
por unidad
Cantidad mínima de pedido: 1
Tiempo de entrega a nuestro almacén: 2-4 weeks
Este precio es válido hasta la siguiente lista de precios o hasta agotar existencias

Información técnica

Estado del artículo Nuevo
Nombre del fabricante Wireless actuator constant current LED dimmer switch
Marca ELTAKO
Categorías Dispositivos de bus KNX/Modbus
País de origen* CN
* El país de origen real puede variar según el lote de suministro. Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
Código del Sistema Armonizado 8526 9200 00
ETIM EC001094
Tipo de fijación Montaje en superficie (yeso)
Modelo Actuador de regulación
Número de salidas 1
Sistema de bus KNX No
Sistema de bus inalámbrico Sí
Sistema de bus Powernet No
Otros sistemas de bus No
Entrada para mando auxiliar No

Detalles del embalaje

Nivel de embalaje 1 4010312314357, 4010312314357
Nivel de embalaje 2 4010312314357
Nivel de embalaje 3 4010312314357

Otros datos técnicos

Frecuencia 50 Hz
Con comunicación por bus No
Tipo de carga Capacitivo
Tensión 12-36 V
Sistema de bus LON No
Posibilidad de funcionamiento en paralelo No
Manejo local/manual No
Potencia de salida 30 W
Grado de protección (IP) IP20
Con indicador LED No
Apto para aumento de potencia No
Sistema de bus inalámbrico KNX No
Radio bidireccional Sí
Módulo de bus desmontable No
Profundidad mín. de la caja empotrada 33 mm

Descargas

Descripción

DC constant current source for LEDs up to 1000mA or 30 watts. Only 0.3 watt standby loss. With adjustable minimum brightness and dimming speed. With switching operation for children's rooms and snooze function. Also with light scene control by PC or wireless pushbuttons. Encrypted wireless and repeater function are switchable. For installation. 45mm long, 45mm wide, 33mm deep. The nominal output current can be set with a jumper on the circuit board: no connection: 350mA, flush right (Pin 2-3 connected): 700mA, flush left (Pin 1-2 connected): 1000mA. Factory settings 700mA. The input voltage ranges from 12V DC to 36V DC maximum. The input voltage must be selected to the sum of the LED at the output voltage, so that the current control can operate. This deviation must be at least 6 volts. The total power output current x output voltage should not exceed 30 watts. A pulse resistant DC power supply unit is required, which provides the necessary voltage and required current of the LED light(s). Universal control voltage input 8 to 230V UC, electrically isolated from the 230V supply voltage and switching voltage. The brightness level is stored on switch-off (memory). In case of a power failure the switch position and the brightness stage are stored and may be switched on when the power supply is restored. Automatic electronic overload protection and overtemperature switch-off. You can teach in encrypted sensors. You can switch on bidirectional wireless and/or a repeater function. The minimum brightness (fully dimmed) is adjustable with the upper %lamp rotary switch. In the setting LRN up to 35 pushbuttons can be assigned, of which one or more central pushbuttons. The dimming speed can be adjusted with the lower dimming speed rotary switch. In addition to the wireless control input via an internal antenna, this universal dimmer switch can also be controlled locally by a conventional 230V control switch if fitted previously. A short interruption of control changes the direction of dimming. Short control commands switch on/off. The pushbuttons can be either taught-in as direction pushbuttons or universal pushbuttons: As direction pushbutton switch on and dim up is on one side and switch off and dim down on the other side. A double-click on the switch on side triggers the automatic dimming up to full brightness with dim speed time. A double-click on the switch off side triggers the snooze function. The children's room function is triggered on the switch on side. As a universal pushbutton the direction change is made by briefly releasing the pushbutton. With switching operation for children's rooms and snooze function. Central pushbutton on switches on with memory value. Central pushbutton off switches off. Switching operation for children's rooms (universal pushbutton or direction pushbutton on the switch-on side): If the light is switched on by holding down the pushbutton, it starts at the lowest brightness level after approx. 1 second and dims up slowly as long as the pushbutton is held down without modifying the last stored brightness level. Snooze function (universal pushbutton or direction pushbutton on the switch-off side): With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off. The current dimming position as well as the adjustable minimum brightness level determine the dimming time (max. = 60 minutes) which can be reduced as required. It can be switched off at any time by short-time control commands during the lighting is dimmed down. Light scenes via app are set and retrieved using the Professional Smart Home controller. Lights scenes with wireless pushbuttons are taught in on the FKLD61 device. Up to four brightness values which can be taught-in in light scene pushbuttons with double rocker. A FBH can either be taught-in as a movement detector with/without twilight switch or a FAH as a twilight switch according to the operating instructions. The LED performs during the teach-in process according to the operating instructions. It shows wireless control commands by short flickering during operation.