Regístrese para desbloquear sus precios B2B exclusivos y empezar a comprar. ¡Regístrese ahora!
Impulse switch with tungsten pre-contact, 1 NO contact 16A image 1

Impulse switch with tungsten pre-contact, 1 NO contact 16A

Solo bajo pedido
EAN: 4010312206744
MPN: 21100801
Embalaje: 1
Precio (sin IVA)
52,45 €
por unidad
Cantidad mínima de pedido: 1
Tiempo de entrega a nuestro almacén: 2-4 weeks
Este precio es válido hasta la siguiente lista de precios o hasta agotar existencias

Información técnica

Estado del artículo Nuevo
Nombre del fabricante Impulse switch with tungsten pre-contact, 1 NO contact 16A
Marca ELTAKO
Categorías Relés biestables
País de origen* CN
* El país de origen real puede variar según el lote de suministro. Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
Código del Sistema Armonizado 8536 4900 00
ETIM EC000188
Tipo de fijación Carril DIN
Función Interruptor electrónico
Tensión de control 1 8-230 V
Tipo de tensión de control 1 AC/DC
Corriente nominal de conmutación 16 A
Número de contactos normalmente abiertos 1

Detalles del embalaje

Nivel de embalaje 1 4010312206744, 4010312206744
Nivel de embalaje 2 4010312206744
Nivel de embalaje 3 4010312206744

Otros datos técnicos

Profundidad de montaje 58 mm
Ancho en módulos 1
Tensión de control 2 230 V
Tipo de tensión de control 2 AC
Frecuencia de la tensión de control 1 50 Hz
Frecuencia de la tensión de control 2 50 Hz
Apto para accionamiento manual No
Corriente máx. de conmutación (cos phi = 0,6) 4 A
Carga máx. de lámparas incandescentes 3300 W
Carga máx. de lámparas fluorescentes 1000 VA
Carga máx. de lámparas fluorescentes (circuito doble) 1000 VA
Carga máx. de lámparas fluorescentes (compensación en paralelo) 500 VA
Número de contactos normalmente cerrados 0
Número de contactos conmutados 0

Descargas

Descripción

1 NO contact potential free 16A/250V AC with tungsten pre-contact. 230V LED lamps up to 600W, incandescent lamp load up to 3300W. Max. inrush current 500A/2ms. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can still switch in zero passage when switching 230V AC 50Hz and therefore drastically reduce wear. Simply connect the neutral conductor to the terminal (N) and L to 1(L) for this. This gives a standby consumption of only 0.1 Watt. Universal control voltage 8 to 230V UC. Low switching noise. No permanent power supply necessary, therefore no standby loss. By using a bistable relay coil power loss and heating are avoided even in the on mode. The relay contact can be open or closed during start-up. It is synchronised at first operation. The electronics does not have an internal power supply and therefore no power is consumed in any contact position. A control current flows only during a short control impulse of 0.2 seconds. This activates the microcontroller, reads the last switching state from the non-voltage memory, switches the bistable relay to its opposite state accordingly and rewrites the new switching state to memory.