Regístrese para desbloquear sus precios B2B exclusivos y empezar a comprar. ¡Regístrese ahora!
Impulse switch with integrated relay function, 1 NO contact 10A image 1

Impulse switch with integrated relay function, 1 NO contact 10A

Solo bajo pedido
EAN: 4010312107911
MPN: 61100001
Embalaje: 1
Precio (sin IVA)
39,51 €
por unidad
Cantidad mínima de pedido: 1
Tiempo de entrega a nuestro almacén: 4-6 weeks
Este precio es válido hasta la siguiente lista de precios o hasta agotar existencias

Información técnica

Estado del artículo Nuevo
Nombre del fabricante Impulse switch with integrated relay function, 1 NO contact 10A
Marca ELTAKO
Categorías Relés biestables
País de origen* CN
* El país de origen real puede variar según el lote de suministro. Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
Código del Sistema Armonizado 8536 5080 00
ETIM EC000188
Tipo de fijación Montaje empotrado (yeso)
Función Electrónico con retardo de desconexión
Tensión de control 1 8-230 V
Tipo de tensión de control 1 AC
Tipo de tensión de alimentación AC/DC
Tensión de alimentación 230 V
Corriente nominal de conmutación 10 A
Número de contactos normalmente abiertos 1

Detalles del embalaje

Nivel de embalaje 1 4010312107911, 4010312107911
Nivel de embalaje 2 4010312107911
Nivel de embalaje 3 4010312107911

Otros datos técnicos

Profundidad de montaje 58 mm
Ancho en módulos 1
Tensión de control 2 10-230 V
Tipo de tensión de control 2 DC
Frecuencia de la tensión de control 1 50 Hz
Frecuencia de la tensión de control 2 50 Hz
Apto para accionamiento manual No
Carga máx. de lámparas incandescentes 2000 W
Carga máx. de lámparas fluorescentes 1000 VA
Carga máx. de lámparas fluorescentes (circuito doble) 1000 VA
Carga máx. de lámparas fluorescentes (compensación en paralelo) 500 VA
Número de contactos normalmente cerrados 0
Número de contactos conmutados 0

Descargas

Descripción

1 NO contact not potential free 10A/250V AC. 230V LED lamps up to 600W, incandescent lamp load up to 2000W. Off delay impulse switch with switch-off early warning and pushbutton permanent light switchable. Standby loss 0.7 watt only. For installation. 45mm long, 45mm wide, 18mm deep. Zero passage switching to protect contacts and lamps. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. By using a bistable relay coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. Control voltage 230V. In addition electrically isolated universal control voltage from 8 to 230V UC. Supply voltage and switching voltage 230V. Very low switching noise. Variable time range up to 120 minutes in the function ESV. At the control input pushbuttons with a glow lamp ­current up to 50mA can be connected. In case of a power failure the system is disconnected in a preset sequence. If the timing period is set to minimum in the function ESV, the release delay is switched off. The standard impulse switch function ES is then set. The function ER is selectable. If the function ER is selected a glow lamp current is not permitted. Only the control input A1-A2 should be used. When set to the function ER this device is suitable to feed back the switching voltage signal of a dimmer switch. If switch-off early warning function is switched on, the light starts flickering approx. 30 seconds before time-out. This is repeated three times at decreasing time intervals. If the permanent light function is switched on, the function can be activated by pressing the pushbutton for longer than 1 second. This function switches off automatically after 2 hours or by pressing the pushbutton for longer than 2 seconds. If both switch-off early warning function and permanent light by pushbutton are set, the switch-off early warning function is activated before switching off the permanent light.