Información técnica
| Estado del artículo |
Nuevo |
| Nombre del fabricante |
Multifunction impulse switch with integrated relay function, 1 + 1 NO contacts 10A |
| Marca |
ELTAKO
|
| Categorías |
Relés biestables
|
| País de origen* |
CN |
|
* El país de origen real puede variar según el lote de suministro.
Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
|
| Código del Sistema Armonizado |
8536 5080 00
|
| ETIM |
EC000188
|
| Tipo de fijación |
Montaje empotrado (yeso) |
| Función |
Otros |
| Tensión de control 1 |
8-230 V |
| Tipo de tensión de control 1 |
AC |
| Tipo de tensión de alimentación |
AC/DC |
| Tensión de alimentación |
230 V |
| Corriente nominal de conmutación |
16 A |
| Número de contactos normalmente abiertos |
2 |
Detalles del embalaje
| Nivel de embalaje 1 |
4010312108079, 4010312108079 |
| Nivel de embalaje 2 |
4010312108079 |
| Nivel de embalaje 3 |
4010312108079 |
Otros datos técnicos
| Profundidad de montaje |
58 mm |
| Tensión de control 2 |
10-230 V |
| Tipo de tensión de control 2 |
DC |
| Frecuencia de la tensión de control 1 |
50 Hz |
| Frecuencia de la tensión de control 2 |
50 Hz |
| Apto para accionamiento manual |
No |
| Corriente máx. de conmutación (cos phi = 0,6) |
8 A |
| Carga máx. de lámparas incandescentes |
2000 W |
| Carga máx. de lámparas fluorescentes |
1000 VA |
| Carga máx. de lámparas fluorescentes (circuito doble) |
1000 VA |
| Carga máx. de lámparas fluorescentes (compensación en paralelo) |
500 VA |
| Número de contactos normalmente cerrados |
0 |
| Número de contactos conmutados |
0 |
Descargas
Descripción
1+1 NO contacts potential free 10A/250V AC. 230V LED lamps up to 200W, incandescent lamp load up to 2000W. No standby loss. For installation. 45mm long, 45mm wide, 32mm deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. Universal control voltage 8 to 230V UC. No permanent power supply necessary, therefore no standby loss. By using bistable relays coil power loss and heating is avoided even in the on mode. The switched consumer may not be connected to the mains before the short automatic synchronisation after installation has terminated. The functions of the second rotary switch are preselected using the rotary switch ES/ER. The setting ER selects the function in brackets. 10 different functions are selectable. 2S = Impulse switch with 2 NO contacts. (2R) = Switching relay with 2 NO contacts. WS = Impulse switch with 1 NO contact and 1 NC contact. (WR) = Switching relay with 1 NO contact and 1 NC contact. SS1 = Impulse multi circuit switch 1+1 NO contacts for switching sequence 0 - contact 1 (1-2) - contact 2 (3-4) - contacts 1+2. (RR) = Switching relay (closed-circuit current relay) with 2 NC contacts. SS2 = Impulse multi circuit switch 1+1 NO contacts for switching sequence 0 - contact 1 - contacts 1+2 - contact 2. (EW) = Impulse relay for fleeting NO contact with 1 NO contact and 1 NC contact, wiping time 1 sec. GS = Impulse group switch 1+1 NO contacts for switching sequence 0 - contact 1 - 0 - contact 2. (GR) = Group relay 1+1 NO contacts (relay with alternating closing contacts). This relay is not suitable to feed back the switching voltage signal of a dimmer switch. Use only relays ESR12DDX-UC, ESR12NP-230V+UC or ESR61NP-230V+UC for this purpose. The electronics does not have an internal power supply and therefore no power is consumed in any contact position. A control current flows only during a short control impulse of 0.2 seconds. This activates the microcontroller, reads the last switching state from the non-voltage memory, switches the bistable relay to its opposite state accordingly and rewrites the new switching state to memory.