Información técnica
| Estado del artículo |
Nuevo |
| Nombre del fabricante |
Impulse switch, 2 NO contacts 16A |
| Marca |
ELTAKO
|
| Categorías |
Relés biestables
|
| País de origen* |
CN |
|
* El país de origen real puede variar según el lote de suministro.
Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
|
| Código del Sistema Armonizado |
8536 5080 00
|
| ETIM |
EC000188
|
| Tipo de fijación |
Carril DIN |
| Función |
Interruptor electrónico |
| Tensión de control 1 |
8-230 V |
| Tipo de tensión de control 1 |
AC/DC |
| Corriente nominal de conmutación |
16 A |
| Número de contactos normalmente abiertos |
2 |
Detalles del embalaje
| Nivel de embalaje 1 |
4010312108048, 4010312108048 |
| Nivel de embalaje 2 |
4010312108048 |
| Nivel de embalaje 3 |
4010312108048 |
Otros datos técnicos
| Profundidad de montaje |
58 mm |
| Ancho en módulos |
1 |
| Tensión de control 2 |
230 V |
| Tipo de tensión de control 2 |
AC |
| Frecuencia de la tensión de control 1 |
50 Hz |
| Frecuencia de la tensión de control 2 |
50 Hz |
| Apto para accionamiento manual |
No |
| Corriente máx. de conmutación (cos phi = 0,6) |
4 A |
| Carga máx. de lámparas incandescentes |
2000 W |
| Carga máx. de lámparas fluorescentes |
1000 VA |
| Carga máx. de lámparas fluorescentes (circuito doble) |
1000 VA |
| Carga máx. de lámparas fluorescentes (compensación en paralelo) |
500 VA |
| Número de contactos normalmente cerrados |
0 |
| Número de contactos conmutados |
0 |
Descargas
Descripción
2 NO contacts potential free 16A/250V AC. 230V LED lamps up to 200W, incandescent lamp load up to 2000W. No standby loss. Modular device for DIN-EN 60715 TH35 rail mounting. 1 module = 18mm wide, 58mm deep. Either universal control voltage 8 to 230V UC at the control input +A1/A2 or 230V with glow lamp current up to 5mA at the control input (L)/-A2 (N). The simultaneous use of two potentials at the control inputs is not permitted. Very low switching noise. No permanent power supply necessary, therefore no standby loss. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. By using a bistable relay coil power loss and heating is avoided even in the on mode. The relay contact can be open or closed when putting into operation. It will be synchronised at first operation. Same terminal connection as the electromechanical impulse switch S12-200-. Maximum current across both contacts 16A for 230V. If this impulse switch is in a circuit, which is monitored by a FR12-230V mains disconnection relay, no additional base load is required. However, the monitoring voltage of the FR12-230V must be set to max. The electronics does not have an internal power supply and therefore no power is consumed in any contact position. A control current flows only during a short control impulse of 0.2 seconds. This activates the microcontroller, reads the last switching state from the non-voltage memory, switches the bistable relay to its opposite state accordingly and rewrites the new switching state to memory.