Regístrese para desbloquear sus precios B2B exclusivos y empezar a comprar. ¡Regístrese ahora!
DALI relay module 8A for flush-mounted box (DT7) image 1

DALI relay module 8A for flush-mounted box (DT7)

Solo bajo pedido
EAN: 4010312324035
MPN: 33000007
Embalaje: 1
Precio (sin IVA)
114,82 €
por unidad
Cantidad mínima de pedido: 1
Tiempo de entrega a nuestro almacén: 4-6 weeks
Este precio es válido hasta la siguiente lista de precios o hasta agotar existencias

Información técnica

Estado del artículo Nuevo
Nombre del fabricante DALI relay module 8A for flush-mounted box (DT7)
Marca ELTAKO
Categorías Dispositivos de bus KNX/Modbus
País de origen* CN
* El país de origen real puede variar según el lote de suministro. Para confirmar el país de origen concreto, póngase en contacto con su gestor de cuenta.
Código del Sistema Armonizado 8542 3190 00
ETIM EC001097
Sistema de bus KNX No
Con comunicación por bus Sí
Sistema de bus LON No
Sistema de bus inalámbrico KNX No
Radio bidireccional No

Detalles del embalaje

Nivel de embalaje 1 4010312324035, 4010312324035

Otros datos técnicos

Tipo de fijación Montaje empotrado (yeso)
Corriente nominal 10 A
Potencia de salida 1000 W
Tensión nominal de funcionamiento 230 V
Sistema de bus inalámbrico No
Sistema de bus Powernet No
Potencia máx. de conmutación 1000 W
Número máx. de contactos de conmutación 1
Corriente de conmutación máx. 8 A
Otros sistemas de bus Otros
Apto para carga C No
Posibilidad de conectar fases diferentes No
Manejo local/manual No
Grado de protección (IP) IP20
Con indicador LED No
Ampliable modularmente No
Módulo de bus desmontable No
Indicador de potencia LED máx. 1000 W

Descargas

Descripción

Module to control a relay contact over the DALI bus (DT7) for luminary installation and flush-mounted box. 59x33x15mm. Protection class IP20. DALI current consumption 2.7mA. Compact relay module for direct control of 230V loads over DALI. Loads without DALI input are easily integrated in a DALI circuit. Loads can be switched on/off by DALI commands. The device function complies with the standard for DALI Device Type 7 – switching function (as of Firmware 2.0). Adjustable characteristic for power-up and bus power failure. The DALI RM8 is powered over the DALI bus. No additional power supply is required. Zero passage switch-on. The module re­presents a bus user and is therefore addressable. Configuration via DALI Cockpit PC software. DALI functions and command set: The DALI RM8 can integrate loads on the DALI bus and can then switch them on/off. The DALI RM8 is a control device for non-dimmable loads based on the DALI specifications in IEC 62386-208 (Device Type 7). Accordingly, the switch characteristic is determined by comparing the virtual dim level (VDAP) with 4 switching thresholds. The virtual dim level (VDAP) corresponds to the dim level of a DALI electronic ballast with its corresponding characteristics (limited by MINLEVEL and MAXLEVEL, dimming speed limited by fade time and fade rate). There are 2 switching thresholds in each dimming direction and they are used for comparison with the virtual dim level. Only the applicable switching threshold for the current virtual dimming direction is evaluated. A threshold with the value MASK is inactive and is not used in the comparison. Switch-on/off delays can be implemented with fading. The DALI RM8 is powered from the DALI bus. The relay response to a bus power failure can be configured by the SystemFailureLevel (no change, ON or OFF, factory setting: ON). The power-on response after applying bus power can be set with PowerOnLevel.